Mission Impossible - Final (Part 5)

It's the grand finale now. The last bits. I covered the back with a lining.

Thereafter, the main fabric goes on top. 

Tada!! Done!! After, I used whateve scrape cloth to cover up the bottom of the sofa. A dustcloth is usually used, but since I have extra lining fabric, I used that instead.

Now, to stick on the lace. I found these at a good price in Chinatown. I bought 15 yards. These lace tend to go out of shape at the cut ends, so make sure you tape or glue them securely first.

Stick the lace on the edges of the fabric and wood frame. I did this for the back, and front.

I'm missing the final picture of the finished product. Please wait for an update on this picture soon. 

I'm so happy this project turned out to be a success (Laugh back at mum who mocked me! HA!). There are some parts I'm not satisfied with:

1. Some of the folds on the "Chesterfield effect" (back rest) were not visible due to over stretching of the fabric.

2. Throughout the process, at times when I'm not careful, I injured the wood frame. You can't see it now because the "injured" areas are covered over with lace.

3. I couldn't find a denser foam for the seat cushion area. When I sat down on the sofa, I sank right in. Luckily, I re-used half of the old foam which was dense enough.

4. I should have sent the wood frame to be sanded down and put on a new coat of varnish, however, I was looking at the overall cost, hence decided against it (Since it's for personal use). The frame looks a little old, but it fits right into the theme of my room.

Overall, I'm really satisfied with the outcome. Can't say that I'm keen to embark on another big project. Perhaps when I'm ready again, this time I'll get professional tools to minimize time, effort and back breaking experiences!!

Again, check out the "before" picture.

xxXxx

Mission Impossible (Part 4)

Hello folks!! Another update on the progress of my stunt. 

The last post was mostly about making your own matching buttons. This time, what you see is not completed in a day. It was done during the weekends, span across one month or so. That is because the back rest of the sofa took tremendous time and effort to complete. It felt like forever... 

See? I didn't lie!! The upholstering done is in traditional style - Hammer & Nails! 

To make sure I have a nice snug edge, I had to use cardboard to give it a nice shape when the fabric is flipped over. My chief seamstress was nice enough to sew the piping for me.

Traditionally, you use cut tacks (nails), however, they tend to split my wood, so I changed to a different nail. I use 3 types of nails throughout the upholstering. One for linings, the main nail and the long slim one for hard to reach areas. Also, I had to use this metal bar assist to hammer in the nails. This is mainly to avoid injuring the edges of the wood frame. In upholstering, you want to secure the fabric as close to the edge as possible and be "hidden" from view. 

Look how the edges look neat with the help of the cardboard? I would recommend this even if you are using the staple gun.

I was so happy we bought the 7ft table. It served as a work table to cut the fabric! Remember I kept the old fabric pieces for reference? I'm using them as a template now to cut my fabric.

Ok, this is work I've done for the "Chesterfield" effect. Had to pull the strings taut and nail it down to the frame. It's best you use the nylon thread. I realized that the cotton one I used tends to snap when I nail it down.

Handling the fabric on the "arm" section" is super tough without using the staple gun. Had to get my mum to help position the cardboard and fabric on the wood frame while I pushed down the foam and position the nail into place for hammering!! No pictures to show, but it really was an acrobatic act!! Had to use both hands and a foot. Haha! Like a bunch of monkeys.

Now for the seat foam. This is a piece of cake after the back rest.

Finally!! All nailed at the back.

I really gave a sigh of relief when these two parts are completed. They comprise of the main job to the upholstering. It's quite a good job I've done there. After all the blood, sweat and tears!! So worth it. 

The next post will be the last one on the final touches to complete the job. 

Now I just need a nice cold beer!



xXx

Mission Impossible (Part 3)

Ok, I really did stop for a long while because I hurt my fingers while striping down the old fabric. Not just the striping but accidently hammering into my fingers as well!! Remember, I complained a lot about my finger muscles feeling sore after over-working them? Yes, my fingers felt so stiff that I had to stop to rest them. The recovering process took longer than I thought. Smart me refused to buy a compressor and staple gun because I'm not sure if this project would interest me to invest in one, so I used the most traditional method... Hammer and nails.

So, if you are really keen on upholstering, I would recommend you to use professional tools or some tools that can give you leverage rather then you being a hero... you'll end up like me...

This was done sometime back in mid Nov.

I've already put on a lining with a little stuffing for the seat area and I'm working on the putting on the inner lining for the frame. (I decided to chuck the idea of putting a new webbing after my minor injury)  This is how it looks when it's done.

Next, the buttons. It was hard to find a seamstress who is willing to do the buttons for me.  I knew it took a lot of time and the selling price is just not worth the effort, hence, I figured that's why these shops don't want to do it.  Luckily, I found a shop that sells a gadget that makes these buttons. Hurray!!

Instructions are in Japanese, but they are pretty straight forward with the picture instructions given. I'll just show you a photographed version of this. Start off by drawing and cutting out the template given on the fabric of your choice.

Please use these labelled indications to understand the process below.

First, put the cut fabric on (C), then place the aluminium caps (D) on top of the fabric and push both into the casing (C).

It looks like this

Then, place (E) into the bottom side of casing (B).

Complete the above and place into casing (C). After, place casing (A) into casing (B).

Thereafter, hammer it down hard to secure all parts to form the button.

 

 Remove it from the casing using a pin.

 Now you've got the perfect home-made matching buttons!!

I made a lot of them as they were needed for the back rest. It took some time and they were more fun then the upholstering. :)

That's all I did for that day. I remembered I ran out of nails hence my work was halted. Well, look out for more. I'll be uploading them soon.


(^v^) bisous

Howdy folks! I'm back!

Sorry, sorry!!

I've been so darn comfortable in my own comfort zone that I refused to lift a finger to update my blog. Jeez! I've been staring into the laptop screen and doing all other stuff except what I'm supposed to!!

Fear not!! I did a good job in taking pictures of more progress and keeping them.... (also to make myself feel less guilty too)!!

I'm going to update some pending projects that is finally completed. So stay tuned!!

A big hug and thank you to those who have been constantly checking my blog for updates. I love you all.